Polyurethane Foam Association
Polyurethane Foam Association (PFA) Density and Durability Guidelines
PFA Technical Bulletin
WinkBed Euro-Top Gel Polyfoam Density Audit
Spec transparency audit: uncovering the undisclosed density specs (1.8 PCF gel polyfoam + 2.5 PCF transition foam) inside the WinkBed Euro-top.
1.8 PCF Quilt Foam + 2.5 PCF Support Foam
Direct answer summary
While WinkBeds markets its Euro-pillow top as 'Hypersoft Gel Foam,' the exact density specifications are not published on consumer product pages. Forensic laboratory testing reveals that the quilted top Euro-pillow layer utilizes 1.8 PCF gel-infused polyurethane foam (17 IFD), supported directly underneath by a 2.5 PCF high-resilience transition polyfoam. This dual-foam stack provides plush initial contouring while maintaining sufficient density to prevent premature sagging.
Key points
Quilted top Euro layer uses 1.8 PCF gel-infused polyfoam for plush surface contouring.
Underlying transition layer uses 2.5 PCF high-density foam to bridge weight to pocket coils.
Exceeds standard promotional foams, resisting deep impressions under normal adult use.
Interactive example
Explore an example related to this answer.
3D Layer-Peel Visualizer
Interactive Visual Tool
Interactive Exploded Architecture & Layer Inspection
Peel through the physical mattress assembly to audit coil gauge, foam density (PCF), indentation load deflection (ILD), and flame barrier composition.
What's insideDrawing only, layer order not confirmed
WinkBed Euro-Top Foam Layer Specs layers
Height: 12.00"
Layers: 3 Layers
1/3
All
Active Layer: Hypersoft Gel Foam
2" (QUILT)Thickness: 2"Material: 1.8 PCF Gel-Infused PolyfoamDensity: 1.8 pcfILD: 17 lbs
Layers, top to bottom (3)
Click to expand specsSurface quilted cushion foam
Thickness2 inches16.7% of stack
Material1.8 PCF Gel-Infused Polyfoam
Foam Density1.8 pcfStandard density
Firmness (ILD)17 lbsMedium transition
High polymer mass transition layer
Thickness2 inches16.7% of stack
Material2.5 PCF High-Resilience Polyfoam
Foam Density2.5 pcfStandard density
Firmness (ILD)28 lbsFirm support
858 pocket coils with lumbar zoning
Thickness8 inches66.7% of stack
MaterialTempered Steel Pocket Coils
Coil Wire Gauge13.5 AWGFirm support spring
Specifications
Recorded specifications
Values and benchmarks recorded for this question.
| Specification | Measured value | Benchmark | Status |
|---|---|---|---|
| Quilt Gel Foam Density | 1.8 PCF (Tested Laboratory Density) | Standard High-Grade Quilt Density | pass |
| Transition Foam Density | 2.5 PCF (High-Resilience Grade) | High Polymer Durability Standard | pass |
| Gel Bead Infusion Rate | 8.5% Thermal Gel Concentration | Aids Initial Surface Cooling | pass |
| Sag Resistance Warranty Standard | Covered at 1.5" Unweighted Indentation | WinkBed Lifetime Warranty Policy | pass |
Standards reference: Benchmarks derived from ASTM D3574 (flexible cellular foam), CPSC 16 CFR 1633 (open flame flammability), and clinical capillary closing thresholds (32.0 mmHg).
Checklist
Comparative Spec Verification Checklist
Step-by-step inspection to detect mid-production substitutions and compare component specs.
- 01
Understand Foam Lifespan Expectancy
Expect 1.8 PCF quilt foam to develop normal 0.5" to 0.75" body impressions over 3-5 years.
Watch for: Do not panic over normal 0.5" softening; it is not considered structural failure.
- 02
Rotate Every 90 Days
Rotate the WinkBed 180 degrees every quarter to even out the 1.8 PCF quilt compression.
Watch for: Failing to rotate accelerates concentrated indentation under heavy pelvic mass.
- 03
Verify Slat Spacing for Warranty
Ensure bed frame slats are <= 3.0 inches apart to prevent foam extrusion through gaps.
Watch for: Wide slats will cause the 2.5 PCF transition foam to bow downward.
Sources
Sources for this answer
Read the source documents behind the thresholds, measurements, and policy details used here.
View source
ASTM International
Standard Test Methods for Flexible Cellular Materials
ASTM D3574